ABSTRACT
A sudden outbreak of COVID-19 occurred in December 2019 and its rapid spread over the last two years caused a global pandemic. A special airborne transmission via aerosols called interunit dispersion is risky in a high-density urban environment, which needs more attention. In order to identify the source location of pollutants or viruses under the interunit transmission condition with natural ventilation, this study adopted the inverse Computational Fluid Dynamics (CFD) simulation with the adjoint probability method. The detailed process of the inverse modeling was presented. Also, the possible interunit transmission routes of the pollutants or viruses were analyzed. A three-story building model with single-sided openings was built. Six different combinations of fixed sensor locations were tested, and it was determined that setting sensors in the four corner regions of the building was the optimist strategy. A total of 25 cases with five different wind directions (0°, 45°, 90°, 135°, and 180°) were tested to verify the accuracy of the source location with inverse modeling. The results showed that 67%–78% of the rooms in the building can be identified with a limited number of pollutant sensors and all rooms can be identified with one additional sensor in the downstream room of the building under different wind direction. This research revealed that the inverse modeling method could be used to identify the pollutant source in the coupled indoor and outdoor environment. Further, this work can provide guidance for the pollutant monitor positions in the applications.
ABSTRACT
The spread of the COVID-19 pandemic through the airborne transmission of coronavirus-containing droplets emitted during coughing, sneezing, and speaking has now been well recognized. This study presented the effect of indoor temperature (T∞) on the airflow dynamics, velocity fields, size distribution, and airborne transmission of sneeze droplets in a confined space through experimental investigation and computational fluid dynamic (CFD) modeling. The CFD simulations were performed using the renormalization group k-ε turbulence model. The experimental shadowgraph imaging and CFD simulations showed the time evolution of sneeze droplet concentrations into the turbulent expanded puff, droplet cloud, and fully-dispersed droplets. Also, the predicted mean velocity of droplets was compared with the obtained experimental data to assess the accuracy of the results. In addition, the validated computational model was used to study the sneeze complex airflow behavior and airborne transmission of small, medium, and large respiratory droplets in confined spaces at different temperatures. The warm room showed more than â¼14 % increase in airborne aerosols than the room with a mild temperature. The study provides information on the effect of room temperature on the evaporation of respiratory droplets during sneezing. The findings of this fundamental study may be used in developing exposure guidelines by controlling the temperature level in indoor environments to reduce the exposure risk of COVID-19.
Subject(s)
COVID-19 , Sneezing , Humans , Temperature , Pandemics , Respiratory Aerosols and DropletsABSTRACT
Microwave-driven plasma gasification technology has the potential to produce clean energy from municipal and industrial solid wastes. It can generate temperatures above 2000 K (as high as 30,000 K) in a reactor, leading to complete combustion and reduction of toxic byproducts. Characterizing complex processes inside such a system is however challenging. In previous studies, simulations using computational fluid dynamics (CFD) produced reproducible results, but the simulations are tedious and involve assumptions. In this study, we propose machine-learning models that can be used in tandem with CFD, to accelerate high-fidelity fluid simulation, improve turbulence modeling, and enhance reduced-order models. A two-dimensional microwave-driven plasma gasification reactor was developed in ANSYS (Ansys, Canonsburg, PA, USA) Fluent (a CFD tool), to create 644 (geometry and temperature) datasets for training six machine-learning (ML) models. When fed with just geometry datasets, these ML models were able to predict the proportion of the reactor area with temperature above 2000 K. This temperature level is considered a benchmark to prevent formation of undesirable byproducts. The ML model that achieved highest prediction accuracy was the feed forward neural network;the mean absolute error was 0.011. This novel machine-learning model can enable future optimization of experimental microwave plasma gasification systems for application in waste-to-energy.
ABSTRACT
A key issue with the distribution of vaccines to prevent COVID-19 is the temperature level required during transport, storage, and distribution. Typical refrigerated transport containers can provide a temperature-controlled environment down to −30 °C. However, the Pfizer vaccine must be carefully transported and stored under a lower temperature between −80 °C and − 60 °C. One way to provide the required temperature is to pack the vaccine vials into small packages containing dry ice. Dry ice sublimates from a solid to a gas, which limits the allowable transport duration. This can be mitigated by transporting in a − 30 °C refrigerated container. Moreover, because the dry ice will sublimate and thereby release CO 2 gas into the transport container, monitoring the CO 2 concentration within the refrigerated container is also essential. In the present work, a 3D computational fluid dynamics model was developed based on a commercially available refrigerated container and validated with experimental data. The airflow, temperature distribution, and CO 2 concentration within the container were obtained from the simulations. The modeling results can provide guidance on preparing experimental setups, thus saving time and lowering cost, and also provide insight into safety precautions needed to avoid hazardous conditions associated with the release of CO 2 during vaccine distribution. [ FROM AUTHOR] Copyright of International Communications in Heat & Mass Transfer is the property of Pergamon Press - An Imprint of Elsevier Science and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full . (Copyright applies to all s.)
ABSTRACT
Facemasks have become important tools to fight virus spread during the recent COVID-19 pandemic, but their effectiveness is still under debate. We present a computational model to predict the filtering efficiency of an N95-facemask, consisting of three non-woven fiber layers with different particle capturing mechanisms. Parameters such as fiber layer thickness, diameter distribution, and packing density are used to construct two-dimensional cross-sectional geometries. An essential and novel element is that the polydisperse fibers are positioned randomly within a simulation domain, and that the simulation is repeated with different random configurations. This strategy is thought to give a more realistic view of practical facemasks compared to existing analytical models that mostly assume homogeneous fiber beds of monodisperse fibers. The incompressible Navier-Stokes and continuity equations are used to solve the velocity field for various droplet-laden air inflow velocities. Droplet diameters are ranging from 10 nm to 1.0 µm, which covers the size range from the SARS-CoV-2 virus to the large virus-laden airborne droplets. Air inflow velocities varying between 0.1 m·s-1 to 10 m·s-1 are considered, which are typically encountered during expiratory events like breathing, talking, and coughing. The presented model elucidates the different capturing efficiencies (i.e., mechanical and electrostatic filtering) of droplets as a function of their diameter and air inflow velocity. Simulation results are compared to analytical models and particularly compare well with experimental results from literature. Our numerical approach will be helpful in finding new directions for anti-viral facemask optimization.